Wildwood Tracking website

Techniques
Tracks & Sign
Mammals
Birds
Others
Sign tracking
Compressions
Measurements
Aging
Gaits
Limb/Eye Dominance
Skulls
Awareness
Quizzes
Teams
Search & Rescue
Way of the Scout
Algonquin Winter
   Tracking
Stories
Humour
Booklist
Contributors
Sitemap
About this site
Use of material
Privacy Policy
HomeCompressions

Pressure Release Study, Part II

by Tom Brown, Jr.

In the last issue, we concerned ourselves with a study of the major pressure releases of changing forward motion and foot mapping. In this issue, we will concentrate on pressures against the wall (see Figure 1), which tell how much pressure is exerted on any side, front, or rear of a track. The wall is that part of the track which is formed when the print is placed in the ground, extending from the ground level to the bottom of the track.

TvIII-1pg03-01.jpg (4676 bytes)

Understanding the wall pressure release systems will help you determine how much pressure is placed on the wall, thereby indicating turning, pivoting, sliding, and so many other nuances that are found in each individual track. Keep in mind that I am only covering the major pressure releases and many points are left out in between. These points will become evident when you have put in a few thousand hours of dirt time and are looking for much finer detail. Also, keep in mind, no matter what the soil, these same pressure releases occur in the same order. Of course, on hard dirt you will need a magnifying glass to read the dirt particles that will lay in the ways to be mentioned.

  

Cliff (see figure 2)
Any time a print goes straight in and out, a wall, or cliff will occur. This indicates that there is no pressure against the wall. The cliff is usually at a 90 degree angle from the ground level to the bottom of the track.
TvIII-1pg03-02.jpg (3421 bytes)

  

Ridge (see figure 3)
As pressure is placed against the wall, a small ridge is formed at the ground level that will continue along the outside of the track until the point where the pressure stops. The greatest point of pressure on ridges are marked by peaks. These peaks are very important in determine indicator pressure releases and the exact points of pressure determine subtle changes in movement.
TvIII-1pg03-03.jpg (3481 bytes)

  

Crest (see figure 4)

As the pressure increases against the wall, the ridge is built higher and the dirt begins to crest backwards over the foot. Remember that this pressure release will still stay intact when the foot is removed -because the foot restricts and is pulled out evenly. Any more pressure beyond a crest will result in what is known as a cave or caving (see Figure 5), then continuing on to a cave-in (See Figure 6). Keep in mind that weathering will crumble a crest and it could be misread by an inexperienced tracker.

TvIII-1pg03-04.jpg (3477 bytes) TvIII-1pg03-05.jpg (3319 bytes) TvIII-1pg03-06.jpg (6042 bytes)

  

Plate (see figure 7)

With extreme pressure now against the wall, a huge plate is thrown up. The whole wall rides up and above the ground level resulting in a plating effect. A number of these plates can occur at the same time, the largest ones being the area of greatest pressure.

 

TvIII-1pg03-07.jpg (6669 bytes)

   

Plate Fissure (see figure 8)

Even more pressure now causes the plate to throw long cracks called fissures. Keep in mind, any time the term "crack" is used alone it means that the dirt has cracked or broken due to weath ring and not to stress; fissures refer toe stress. If the pressure continues, then the plate crumbles, showing even greater pressure and stress against the wall (See, Figure 9).

TvIII-1pg03-08.jpg (7493 bytes) TvIII-1pg03-09.jpg (8074 bytes)
  
Explosion (See Figure 10)

An explosion is the greatest amount of pressure and stress any wall can stand and usually means that the wall is completely blown out. This usually takes a very violent motion, and the stress can be judged by the amount of dirt kicked out of the track and the distance it has traveled.

TvIII-1pg03-10.jpg (7008 bytes)

  

Practicing Pressure Releases

All dirt moves in the same way with few exceptions, but all types have their own quirks, depending on consistency, moisture, and composition. Fortunately, these will not affect the major pressure releases listed, but only those minute ones that take much time and study to learn. By the time you get to that point, you know most dirt very well and are aware of the little inconsistencies of the soil you are working with.

To practice pressure releases, it is best to find a damp, sandy beach; being an ocean, lake, or stream will make little difference. Usually, these areas are littered with tracks of men and animals, but it is a good idea to wipe the slate clean and make your own. Practice the various speed variations and changes you learned in the last newsletter, then various turns and pivots. Pick out the pressure releases you see in the illustrations. This way when you make the track you know exactly what you were doing, how fast you were going, and to what degree you turned.

Later, as your skill increases, go for the other human tracks you find, then to the animals. Don't graduate to different dirt until you can master the releases in simple sand situations. Then, slowly bring your skill up by trying more and more difficult dirt until you can see the pressure releases in hard-packed earth in the form of dust particle pilings.

As you get more advanced, you will discover how each digit and portion of a finger or toe can have its own set of pressure releases differing from others on the same foot. This and other advanced methods will be covered in future articles along with some of the more isolated releases and pivots common to all tracks.

Many of you have written to me about the foot mapping portion of the last article and how you thought it could be done better. You are right, providing that is all there is to pressure releases. But, unfortunately, there is so much more, and only that system will work for the more advanced methods and especially correlate to the depth foot mapping that we will discuss in later issues. So please use this method. You'll soon see why it is the only way that will work.

Note

Some people have asked how it would be possible to map a small foot such as a rodent's forepaw. Simply draw to scale, saying that one inch equals one foot, then draw in the pressure releases on the foot map. A magnifying glass is helpful in reading mice and other small animal pressure releases.

TvIII-1pg04.jpg (10377 bytes)


From The Tracker magazine, 1984, published by the Tracker School.
For more articles from The Tracker magazine, visit the Tracker Trail website.